Skip to main content

Concrete letter casting basics

This is a beginner's guide to the basics of casting concrete 
For specific details, search online for how to create concrete casting forms.

To cast concrete with lettering and a logo if desired, you need a form, concrete and letters.
The form can be on a flat surface, into which you can pour your concrete, or the form can be erect with a bottom, sides, a front and a back. Be sure to mix sufficient smooth concrete so that a spill or leak won't scuttle your casting pour. Stir and poke the concrete to reduce incidence of air pockets.

For the sake of simplicity, this article focuses on using a flat form or pan for making pavers.

After deciding on the form or pan shape and size, follow the basic preparation instructions.

I
Reverse-cast metal letters with a 7-degree draft for casting
f you're casting pavers
, especially those with a pattern, design or wording combination, you'll likely want to have a reusable form with multiple-use letters.

Letters made to be reused are generally made of either rubber or metal. Rubber letters are flexible, and so can be compressed to remove from cured (hardened) concrete, and metal letters are made with a 7° draft, which allows them to be removed from the concrete.
The draft (slightly sloped sides of the letters) allows the hardened concrete to release the letters, as the fit is a very slight bit wider at the base of the letter as viewed from the side. Regardless of which you use, you will want to oil the letters once you're ready to pour concrete. The rubber and metal letters are made in reverse like a rubber stamp so that the resulting imprint in the concrete reads correctly.


See below for using single-use foam letters.                              GET A COST ESTIMATE


What is the difference in how the letters work?
As far as the concrete is concerned, there's little discernible difference to the naked eye. The rubber letters are generally 1/8" to 1/4" [3.18mm to 6.35mm] deep, and so the resulting impression is not very deep. This is best for flat pavers, as water and dirt will not make a deep 'pool' on the surface. For a deeper casting, the metal letters we make are an average 3/4" to 1.5" [19mm-38mm] deep, depending on the letter height. These may be better for vertical concrete casting and deeper cast letter effects. Foam (single-use) letters can be 1/2" to 1-2" thick.


Large-cell beaded foam is the most economical but leaves a texture.
What if I only need one imprint cast?

For a single casting (one side of one sign) it's not very cost-effective to buy letters made to be reused. You can use our very economical large beaded foam letters if the resulting letter "texture" is not a problem, or our smoother smooth-cell foam and gator foam materials. Letters in foam materials are removed or dissolved when removing from hardened concrete, and so are single use.




So if you were planning on a mixed-media sign like the one above, we would help you by determining what you need to cast it in concrete (the letters spelling "Sunflower" are embedded in concrete and the panel beneath is made of dimensional letters mounted to a panel shape, which in turn is mounted to the sign face) and to assemble your sign.
We have all the D.I.Y. products you need, made to order.


For pricing on the foam letters, send your project details here. Be sure to include your own contact information, along with:
Form for a hollow-center columnar cast.
  1. Exact wording with the
  2. Size of letters (measured by letter height),
  3. The desired thickness of letters,
  4. Kind of material (foam, metal, rubber)
  5. Typestyle if any, otherwise a bold block like the letter "E" above will be used,  and any
  6. size or space limitations if there are limits, like a 120-foot width and 40" overall sign height. For example, if your casting area is 24 by 60 inches and you have to make the letters fit, tell us the maximum width and height that the letters must fit within.

We can walk you through this- After the first time, it's all common sense.
Did I miss something? Leave a comment below.

Fill in the cost estimate form to tell us what you want us to price for you, or send this to a friend who will be considering this project. 
We're here to help.

Questions or comments are welcome.                                             GET A COST ESTIMATE



Joe Giral is the founder and creative director of LetterBank and My DIY Signs.
Your comments are welcome.



Comments

  1. Howdy, making an artificial rock sign for neighborhood enter

    SANTA HELENA PARK surface are will be about 16 sqft of flat. I have a few designs. Would like letters about 6"and 3/4" thick simple font with a serif look. Eider de Mello (619)228-3823 or eiderskater@yahoo.com

    ReplyDelete
  2. This comment has been removed by a blog administrator.

    ReplyDelete
  3. I have recently started a blog, the info you provide on this site has helped me greatly. Thanks for all of your time & work Rectify

    ReplyDelete

Post a Comment

Popular posts from this blog

How to make a simple Do-It-Yourself foam letter sign

Here are a few easy-to-follow steps for making a foam letter sign. Before you start, here are some basic descriptions to help you plan for what you need. You may want to print this out and save this or forward it to someone looking for guidelines. Contents : What are foam letters? Where can I order foam letters? How can I find the cost? How large do the letters need to be? available space (for your sign) how far does the sign need to be readable? aesthetics What do I need to have to make this turn out well? Using the yardstick Before you glue or cement anything in place You're almost there! What are foam letters? By "foam', I refer to the dimensionally stable extruded plastic "foam", which is cut into letters usually from a 4x8-foot master sheet. The sheets are usually available in 1/2", " and 1-1/2" thickness, so for the sake of this brief article, I'll refer to 1" thick letters when I mention foam letters. Foam let

Crafts + DIY: How to Cover over Awnings with our DuraStik Self-Adhesive Fabric

Wait, what? Covering over Awnings can be simple Craft ideas below   So what's the scope of this #DIY craft project? We're going to go over how you can cover an awning that may have out-of-date writing on it to update the business name and information. To repair a tear on an awning tent or sail, jacket, canopy or flag, look here. You can cover over old names and information with DuraStik Why would you need to cover an awning? In the "old days", awnings were decorated with a special paint. The paint won't come off, so the best practice is to cover over with more pain- which can look pretty tacky if it's not done right. Modern awnings may be painted or if they're back-lighted, may have an area where light from behind passes thru the letters. This is called an eradicable awning. How can you use DuraStik self-adhesive woven fabrics? • When you're moving into a new store with an awning, • If the information on your awning is out of date, a